Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Panel Replacement Cost in Hollywood?
Panel replacement in Hollywood typically runs $250 – $500 for a single damaged section, with most homeowners landing near $340 for one to two panels on a standard two-car door. That price covers the panel itself, matching the profile and color, and the labor to swap it in. If more than three sections are bent or rusted through, the math often tips toward a new door, and we’ll tell you when it does.
We’re Benchmark Garage Door Repair, and panel work is one of the three things we do every day alongside garage door repair. When we walk up to a door in Hollywood, we’re not there to sell you a full replacement. We’re there to figure out whether one section, a hinge, or a whole run of panels is actually the problem, then give you a number you can hold us to.
Key Takeaways
- One-panel replacement in Hollywood: $250 – $500, parts and labor together.
- Sectional door panels can’t always be color-matched perfectly on older doors – fading shows the difference.
- Salt air near the beach accelerates rust on steel panels, so Hollywood doors can fail on the coast faster than inland doors.
- If two or more panels are damaged, ask for the per-panel price before you agree to anything.
- Free estimates. Call (833) 589-8332 and we’ll give you a range before we roll a truck.
Panel Replacement Cost Breakdown (2026)
Here’s how the numbers break down for Hollywood in 2026. These are real ranges we work within, not teaser prices. The low end is a basic single panel on a common profile; the high end is a larger or specialty panel, a color match that has to be ordered, or glass and window inserts.
| Line Item | Typical Price Range |
|---|---|
| Single standard steel panel (with labor) | $250 – $360 |
| Two panels, same profile and color | $380 – $500 |
| Insulated or premium panel | $320 – $500 |
| Panel with decorative glass or window inserts | $350 – $500 |
| Panel plus hinge and roller replacement at the same visit | $300 – $500 |
| New garage door installation (when replacement makes more sense) | $700 – $2,200 |
For comparison, related repairs in Hollywood sit in these ranges: spring repair $180 – $340, cable repair $130 – $250, and track realignment $120 – $240. If your door is sagging or off-track rather than visibly dented, the panel may not be the culprit at all. We check the whole system before quoting panels, because a bent panel on a misaligned track will just bend again.
What pushes the price up? A panel that has to be special-ordered because the color run is discontinued, a door with non-standard widths, and any panel that arrives with glass. What keeps it down? Matching a profile that’s still in production and stacking the work – fixing a hinge or roller while we already have the panel off, so you’re not paying a second trip charge.
What Affects Panel Replacement Pricing in Hollywood
- Coastal salt exposure. Doors within a mile or two of Hollywood Beach and the Intracoastal corrode faster. Steel panels near the ocean pit and rust along the bottom edge sooner than the same panel inland in, say, Pembroke Pines. If you’re on the east side, we’ll point out which sections are showing salt damage and which are still solid.
- Brand and profile match. We service Clopay, Amarr, Wayne Dalton, and Raynor doors among the eight brands we’re trained on, so we can often source a matching panel instead of telling you to replace the whole door. A discontinued profile means either a close match with a visible shade difference or a full replacement.
- Sun and heat cycling. South Florida sun bakes the south- and west-facing side of a door. Panels there warp and the finish chalks sooner, which shows up as color mismatch when a new panel goes next to an old, sun-faded one.
- How many panels are damaged. One dent is a repair. Four damaged panels on a six-panel door is usually a replacement conversation, and we’ll show you both prices so you can decide.
- Door material. Steel is the most affordable to replace a section on. Wood and aluminum-composite doors cost more to match and often need finishing work.
- Window inserts and insulation. A panel with glass or a foam core costs more than a plain steel section, and the labor to reseal glass adds a little.
One local detail that comes up often: Hollywood has a lot of older ranch and mid-century homes with original 16-foot single-car-wide double doors. Those panels are narrower than modern standard sections, so a match sometimes has to be custom-ordered. That adds time, not always much money. We’ll tell you upfront which way yours leans.
How to Save on Panel Replacement
The biggest savings come from acting before one dent becomes three. A single panel replaced early is a $250 – $360 job. Wait until the door sags and the track bends, and you’re looking at panel work plus track realignment plus possibly a spring.
- Get the per-panel price in writing. Ask for the cost of each panel and the labor separately. Some companies quote a flat “panel job” that balloons once they’re on site.
- Bundle small repairs. If a hinge or roller is worn, have it done during the panel swap. It’s cheaper than a return visit, and we can roll it into the same estimate.
- Match in production, not discontinued. When your panel profile is still being made, the price drops and the color match is cleaner. We’ll check what’s available for your door before recommending anything.
- Know when to stop repairing. If the quote climbs past roughly half the cost of a new door, a new door starts to make sense – and we carry Clopay, Amarr, Wayne Dalton, and Raynor lines that aren’t sold at the big-box stores. New doors run $700 – $2,200 installed.
- Rinse the door bottom occasionally. A quick rinse of the bottom panel near the beach removes salt film and slows corrosion. It won’t fix a rusted panel, but it buys time on the ones still solid.
Free estimates are standard here. Call (833) 589-8332 and we’ll give you a realistic range over the phone, then confirm it on site. No pressure to replace what doesn’t need replacing.
How Do You Know If a Panel Needs Replacing or Repairing?
A panel needs replacing when it’s cracked, holed, rusted through, or bent so badly the door no longer closes flush. A panel that’s merely scratched, faded, or has a small dent can often be left alone or touched up. The test is simple: if the door seals flat against the floor and the panels are structurally sound, you’re not replacing anything yet.
In Hollywood we see a specific pattern. Doors on the beach side rust from the bottom up because of salt spray off the ocean, and doors on the inland west side (think Hollywood Hills, Emerald Hills) tend to suffer sun warping and impact damage from storms and yard equipment. The rust case is usually a real replacement. The sun case is often cosmetic until the panel bows, at which point the door won’t seat properly and you’ll feel a draft or hear rattling.
We diagnose to a measurable standard before recommending anything. If a hinge is bent and the panel is straight, we fix the hinge. We don’t sell you a panel you don’t need. That’s what Benchmark means to us.
Can You Match the Color of a Replacement Panel?
Usually, yes, if the door’s original color run is still in production. Clopay, Amarr, Wayne Dalton, and Raynor all maintain standard color lines, and we can often order a matching panel. The catch is fading – a ten-year-old door beside a brand-new panel in the “same” color will show a shade difference under Florida sun.
When an exact match isn’t possible, you have options: replace the panels on the full visible side for a consistent look, accept a close match, or move to a full door replacement if the mismatch would bother you. For doors on the Fort Lauderdale side of the market, our Panel Replacement in Fort Lauderdale page covers the same process and how we handle color matching there.
How Long Does Panel Replacement Take?
A single panel replacement takes about one to two hours on site once the correct panel is in hand. If the panel has to be ordered, expect a few days to a couple of weeks depending on the profile and color. We’ll tell you which bucket your door falls into before you commit.
Multiple panels or a full run take longer, and if the track or springs need attention at the same time, add an hour or two. We schedule panel work as its own job, not squeezed between calls, so you get a real time window.
Do You Work on All Garage Door Brands?
We service the eight brands you’re most likely to have installed – LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor – so we work on what’s already on your house. That matters for panel work because a dealer-tied company will only quote their own line. A brand-agnostic approach means the recommendation is driven by your door’s condition, not by which product earns the most margin.
If you’ve got an opener problem too, that’s a separate service line we handle. Opener repair is a dedicated discipline here, not an afterthought, covering mechanical failures, motor issues, and smart-home integration problems. If your opener is acting up, we’d rather you tell us at the estimate so we can look at both.
FAQs – Panel Replacement Cost in Hollywood
How much does it cost to replace one garage door panel in Hollywood?
$250 – $500 for a single standard panel, parts and labor together, with most jobs near $340. Premium or insulated panels and panels with glass sit toward the top of that range. Call (833) 589-8332 for an exact quote – estimates are free.
Is it cheaper to replace a panel or the whole door?
Replacing one or two panels is cheaper, usually $250 – $500 versus $700 – $2,200 for a full door. But once the damage crosses roughly half the cost of a new door, or several panels and the track are involved, replacement wins on value. We’ll price both so you can compare.
Can you come today to look at a damaged panel?
Often, yes – call (833) 589-8332 and we’ll tell you the soonest available window. We don’t promise same-day service as a blanket guarantee, but we’ll be straight with you about timing and put you on the schedule that fits.
Why is my panel rusting so fast in Hollywood?
Salt air. Doors near Hollywood Beach and the Intracoastal pick up salt film that speeds up corrosion on steel panels, especially along the bottom edge where moisture sits. A rinse every few weeks slows it. Once a panel is rusted through, replacement runs $250 – $500.
Does a panel replacement come with a warranty?
Panel manufacturer warranties carry through the panel itself; our labor coverage is confirmed on your written estimate, so ask and we’ll spell it out before any work starts. Call (833) 589-8332 with your door’s make and we’ll walk you through what applies.
Pricing reflects the Hollywood market as of 2026. Benchmark Garage Door Repair offers free estimates – call (833) 589-8332.
What Our Customers Say
"The old chain drive sounded like a freight train through the bedroom above the garage. Went with the belt drive they recommended and now I genuinely cannot hear it open from upstairs."
— Grace Kim"Keypad stopped working, which I assumed meant a whole new system. It was the batteries and a reprogram. He charged me the minimum service call and told me how to do it myself next time."
— Javier Morales"Logic board on a 15 year old opener. He was upfront that a new opener would cost less than the board plus labor, and he wasn't wrong. No pressure either way."
— Chris Fletcher